Repairs to uPVC Windows

uPVC is a fantastic choice for modern homes. They are long-lasting, durable and easy to maintain. In contrast to aluminium and timber, they do not rust or window replacement near me rot.

It is important to clean and oil UPVC doors and windows on a regular basis. This will save you from costly repairs and improve energy efficiency.

1. Broken Glass

The damaged glass in your windows can cause serious damage to your home, and could even be fatal. It is essential to take the time to ensure that you're doing everything you can to ensure that your windows are in good condition.

Single-pane windows are relatively simple to replace, and they typically fit into frames of the past easily. If windows with double panes are held together by internal beading, it will be difficult to remove and replace the panes that were previously in use. In this instance it is essential to purchase plastic spacers in order to make sure that the new pane fits into the window frame.

If you plan to try to remove the glass panes yourself, it is essential to wear the appropriate safety equipment, including thick gloves and eye protection. It is also recommended to lay down a dropcloth before you begin working on the window panes so that any shards fall on the fabric and not onto the floor which could cause them to be trampled.

It's a good idea to seal the gap after the glass has been removed. This will prevent water and drafts from entering your property until a professional comes out to repair the window. This will also act as a barrier that will prevent any intruders from gaining entry to your home. If the gap between the door and the window is significant, you may prefer security screens that has windows. This will give you the best of both.

2. Sagging

uPVC is durable, energy-efficient and affordable alternative to timber sash windows. Over time, they can develop a variety of issues such as sliding. A sagging uPVC window can cause issues with light, draughts, and even security. If you notice that your uPVC window is beginning to shrink, it is important to act swiftly to prevent the problem from worsening.

Repositioning the hinges can aid in fixing a window which is sagging. You'll first need to open the windows so you can reach the frame. With the screwdriver, you'll be able to unscrew the hinges at the top and bottom and adjust them by turning them clockwise or counter-clockwise. After you've repositioned the hinges, close your window and test it for fitting. If you're satisfied with the fit, you can tighten the screws to ensure that they remain in place.

If you are unable to move the hinges, you might need to replace the seal. As time passes, rubber seals lose their elasticity and dry out and cause their tightness to decrease. If this happens, it's crucial to replace the seal as quickly as you can to ensure that your uPVC windows remain watertight and secure from draughts.

UPVC handles can also loosen up. Most often this is due to screws that have become loose over time. However, it could be due to the fact that the handle mechanism has worn out. It's relatively easy to fix a loose uPVC handle. The first step is to close the window and then perform a test fit. The joints at the corners of the sash should be aligned with the joint on the casing. If it isn't, you can use a screwdriver to loosen the handle and reverse the mechanism back into its original position.

3. Water Leaks

If you wake up to wet floors and mouldy walls each time it rains it's important to take action. The leaks of water from windows do are not just a cause for degrading of the structure of your home but also undermine your efforts to control the temperature in your home. Most often, uPVC window leaks are caused by a damaged or missing sealant.

This is a fairly simple fix that can be done by any competent DIYer. Depending on the severity of the problem is, the old caulking may have to be removed. When it is time to uPVC repair, you must avoid 'over-caulking'. This will only make your window more difficult to clean and lower its energy efficiency.

Check that any drainage holes do not have debris in them, and also that the sill pan has been properly angled to allow the water to drain from the window. In more serious situations, you might have to consider replacing the window.

Moldy sills and rotten ones are another sign of water leakage. This is a fungus that thrives in damp conditions and can quickly spread across the house.

It is also important to remember that if the leak is coming from between the glass of your double glazed windows, it's more likely to be a problem with the glass seal, rather than the frame or sliding. This can be easily fixed by an uPVC window expert who can replace the glass seal and restore the full insulation properties of your windows.

4. Faulty Hinges

If your uPVC windows are stiff to open, or slack and open with ease, it may be hinges that are at fault. These are easily replaced by any competent DIYer and can usually be done within a few minutes.

Like any mechanical part, hinges can wear out over time. The process of replacing a hinge on a window is essentially a very simple process, but it's simpler when you have a person to help hold the frame in place.

It is also important to verify that the uPVC hinges are being opened and closed in the correct direction. You can do this by looking for the arrows on each hinge, this indicates the direction in which the window doctor near me should be opened.

The issue can be caused either due to opening the window in the wrong way or by a poor installation at the factory. Sending us a picture via our website will often resolve the problem. We are happy to offer advice.

Regularly lubricating the hinges is also necessary. This can be accomplished by applying a light engineering oil on the hinges. We suggest using a solvent-free lubricant, such as 3-in-one Multi-Purpose Oil. Regular lubrication will make the window easier to open and close. It can also prevent corrosion and decrease the chance of sticking. It is recommended to perform this every year. WD40 or other solvent-based oils should not be used since they can damage your uPVC windows.

5. Draughts

Draughts in windows made of upvc can be caused by different things. The hinges can also become disaligned as a result of wear, causing a gap where the sash meets frame. If they're beyond repair, it might be necessary to get them re-aligned. In addition, the interlock could also become disaligned. This is located on the hinge's side and could require to be cleaned. In some instances it is possible to replace these.

These seals are susceptible to wear and tear or become damaged over time, double glazing allowing air to escape. This can be avoided by replacing them with high-quality weatherstripping. Replace the windows made of Upvc with low-emissivity glass. This will help control indoor temperatures and decrease the possibility of draughts.

Another, and most effective ways to cut down on the draughts in your home is to use an draught excluder. These are usually fabric tubes which are filled with a kind of filler. They can be put on top of your windowsill. These will keep your home warm by blocking out cold air.

With a bit of regular maintenance and repair your windows made of upvc will continue to provide an excellent level of security and insulation for your home. It is important to remember that all windows eventually wear out and it is more cost-effective to replace them instead of fixing them. If you encounter any issues with your Upvc window, it's best to consult a professional immediately.